Tech News Today, Marshmallow Custom Rom, Huawei, Run Programs, Network, Chromebook, Bank Account

Jumat, 25 November 2011

Introduction about Mobile Phone IC's( Integrated Circuits )

Introduction about Mobile Phone IC's( Integrated Circuits ) - To all visitors of this blog, I say welcome and thank you for visiting the blog Tech News Today Look for all the things you need that are available on this blog. If not available, please leave suggestions and comments for the development of this blog. now we will discuss first about Introduction about Mobile Phone IC's( Integrated Circuits ) we have collected a lot of information from sources to create this article, so please see.

Articles : Introduction about Mobile Phone IC's( Integrated Circuits )
full Link : Introduction about Mobile Phone IC's( Integrated Circuits )

You can also see our article on:


Introduction about Mobile Phone IC's( Integrated Circuits )

Integrated Circuits


There are Complete notes about Main IC's  in mobile phones and How can you identify its. Not only that but also you can get a real idea about mobile phone damages or faults which are comes with IC. Specially there are three main type IC s in mobile phone. These are

  1. Pin IC
  2. Path IC
  3. MBGA ( Micro Ball Grid Array ) 

  • Pin IC

Integrated Circuits are complex circuits which have been etched onto tiny chips of semiconductor. When we think about Pin IC, The chip is packaged in a plastic holder with pins  which will fit the holes on stripboard and breadboards. Very fine wires inside the package link the chip to the pins.


How Can we numbering the Pins in IC

These pins are which is in Pin IC have been numbered for finding more 100% correctly details about its circuitit. Number 1 is which we can see when we checking anti-clockwise around the IC (chip) starting near the notch or dot.


You can mount and unmount or replace these IC s using SMD rework station. However when you replace like this IC you must mount all pin to the PCB and do not short circuit.Specially Latest mobile phones have not like this IC s. But when you training to mount and unmount these Ic s then you will be able to replace chinease phone display , Switches ... etc.


  • Path IC
When you check your mobile phone PCB , you will be unable to find these ICs quickly .But when you unmount these ICs you can easily identify thats. following images will be helpfull for undersanding about its  ecternal appearance.


Majority ,Power Amp and Antenna Switch are come as this type of IC.However you can mount and unmount easily using SMD Rework station. But unfortunately we can see only two or three ICs on common mobile phones.


MBGA( Micro Ball Grud Array)

The BGA is descended from the pin grid array (PGA), which is a package with one face covered (or partly covered) with pins in a grid pattern. These pins conduct electrical signals from the integrated circuit to the printed circuit board (PCB) on which it is placed. In a BGA, the pins are replaced by balls of solder stuck to the bottom of the package.


These solder spheres can be placed manually or with automated equipment. The solder spheres are held in place with a tacky flux until soldering occurs.The device is placed on a PCB with copper pads in a pattern that matches the solder balls. The assembly is then heated, either in a reflow oven or by an infrared heater, causing the solder balls to melt. Surface tension causes the molten solder to hold the package in alignment with the circuit board, at the correct separation distance, while the solder cools and solidifies.(wikipedia)



You can use Infared , Laser or manual SMD rework station for removing or mounting for BGA. When you have remove BGA IC firstly you want Clean PCB surface and Reballing IC and pcb surface.

After Reballing you can see IC and PCB as following



 Finally you can mount new or reballed IC using Laser, Infared or manual SMD Rework stations.


 Specially Before you Remove your BGA IC firstly try to solve damage soldering or heating. then you can remove that damage IC  and try to replace new one. When you replace that IC some times your phone will be short circuit , if it is short circuit never try to Switch on and try to Soldering otherwise replace again it. However you want get a good experience for doing that therefore you can practice with dead or damage phones. 

.................................................................................................................................................................

This note will help you to understand about Main IC type in mobile phones and about its important. Whatever Try to be a Good Technician. Good Luck 2 U.



information Introduction about Mobile Phone IC's( Integrated Circuits ) has been completed in the discussion.

hopefully the article we give the title Introduction about Mobile Phone IC's( Integrated Circuits ) can provide knowledge for you in living everyday life in determining the gadget that suits your needs.

you just read the article about Introduction about Mobile Phone IC's( Integrated Circuits ) if this article is useful for you and want to bookmark it or share it please use the link https://sihanandi.blogspot.com/2011/11/introduction-about-mobile-phone-ic.html thank you and do not forget to comment if anyone.

Tag :
Share on Facebook
Share on Twitter
Share on Google+
Tags :

Related : Introduction about Mobile Phone IC's( Integrated Circuits )

2 komentar:

  1. If you need to get useful information about Website Blockers for Safety, try to check this out! Here you can find what you need

    BalasHapus
  2. I find it quite useful that today you can install a parental control on your kid's phone and always be aware of where they are and what they do online. There are too many scammers and bullies, unfortunately, and I want to keep my child safe. I found a good monitoring app at https://www.mspy.com - you should check it if you worry about your kid's activity frequently.

    BalasHapus